H3c-technologies H3C MSR 50 Bedienungsanleitung

H3C MSR Series RoutersOAP/OAPS V2 Module Customization User Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Docume

4 Item Quantity Remarks Linux server 1 Provides DHCP and TFTP functions: • The IP address must be 192.168.0.2. • The DHCP and TFTP functions have b

5 Installation procedures To install a Linux operating system: 1. After the router is booted normally, execute the oap reboot slot slot-number comman

6 Hard Disk Size : 500.1GB

7 Start to execute install script file... Check for install...Ok

8 Shutting down NMB services: [ OK ] Stopping snmpd: [ OK ]

9 Module Partition Mount point File system Description Reserved Data partition Installing a Windows operating system The OAP/OAPS module does not hav

10 Configuring the software To configure the software: 1. Create the sub folder tftpboot in the root directory of disk D on your PC. 2. Copy files N

11 Vrefresh=75 Xresolution=1024 Yresolution=768 [MassStorageDrivers] "Intel(R) 5 Series 4 Port SATA AHCI Controller"="

12 "C:\Hotfixes\firstrun.bat" [OSChooser] Description="Windows Professional"—Standard Installation Help="This wi

13 Yresolution=768 [MassStorageDrivers] "Intel(R) ICH8M-E/M SATA AHCI Controller"="OEM" [OEMBootFiles] iaAHCI.cat

Copyright © 2011-2012, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmi

14 [OSChooser] Description="Windows Professional—Standard Installation" Help=" This will install Windows Professional in a stan

15 2. Use the last IP address that the DHCP server assigned (the IP address of the Ethernet port on the OAP/OAPS module) to enable Remote Desktop, to

16 5. Enable the DHCP server function on TFTPD32. Setting up a configuration environment As shown in Figure 3, connect the PC to the console port on t

17 [root@localhost linux-2.6.18.x86_64]# make mrproper [root@localhost linux-2.6.18.x86_64]# make menuconfig 4. Compile and install the kernel and OA

18 Figure 4 Set up the terminal Installing the Ethernet port driver When you upgrade the internal Ethernet port eth0 driver for a MIM-OAPS or MIM-OA

19 Logging in to Windows The OAP/OAPS module does not have an HMI, so you must log in from the PC to the OAP/OAPS module by using Remote Desktop Conne

20 Appendix OAP/OAPS module hardware features Table 9 OAP/OAPS module hardware features Item MIM-OAPS MIM-OAP FIC-OAP Processor Intel Atom N450 Inte

Preface The H3C MSR Series Routesr OAP/OAPS V2 Module Customization User Guide describes hardware specifications of OAP/OAPS V2 modules, configuration

Symbols Convention Description WARNING An alert that calls attention to important information that if not understood or followed can result in perso

MSR 20-2X[40] Routers Installation guide MSR 30 Routers Installation guide MSR 50 Routers Installation guide MSR Series Routers Interface Module Manua

i Contents OAP/OAPS module customization ·············································································································

1 OAP/OAPS module customization Overview A Linux operating system and Windows operating system run separately on an OAP/OAPS module. You can configure

2 Test ALL Memory? Yes or No (Y/N)

3 Operating system boot options The OAP/OAPS module has two storage media: NAND Flash and harddisk. The NAND Flash provides the diagnosing and one-key