H3c-technologies H3C WA2600 Series WLAN Access Points Bedienungsanleitung

H3C WA2620X-AGNP Access Point Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version

5 Port Standards and protocols Function ETH 1 10/100/1000BASE-TX copper port IEEE802.3 IEEE802.3u IEEE802.3at Connects to the Internet or MAN and se

6 Preparing for installation This chapter describes how to prepare for the installation of the AP, including the preparation of tools and installatio

7 Power supply The AP can be powered by a power injector or through PoE+. Power injector You can use an H3C POE5 power injector to power the AP. For

8 Item Requirements Power grounding (AC) • Use a power cord with a protective earth (PE). Do not use a power cord with only an L line and an N line

9 Installing the AP The WA2620X-AGNP AP can be mounted on a pole. To ensure the radio coverage, have the AP installed by professionals. Installing th

10 Figure 5 Adjust the tilt of the AP 1234 (1) Mounting plate (2) Bolt (3) Mounting slot (allows bracket rotation) (4) V-shaped bracket Pole mount

11 Figure 7 Mount the AP on the pole (1) AP (2) Screw (M6 x 12) (3) Mounting plate (4) V-shaped bracket (5) Long bolt (6) #10 flat washer (7)

12 { If there are parapets on the rooftop and the height of the parapets is no less than 1.2 m (3.94 ft), you can fix the pole on a parapet with exp

13 { If there is no parapet on the rooftop, fix the pole to the rooftop surface or a cement pier on the rooftop with expansion screws and stabilize

14 Figure 11 Install omnidirectional antennas 45°45°PoleShielding angleLightning rodOmnidirectional outdoor antennaPoleOmnidirectional outdoor antenn

Copyright © 2011, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted

15 Figure 12 Alternative method for installing an omnidirectional antenna NOTE: In Figure 12, the antenna pole is not fixed on the cement pier.

16 1. Connect the antenna cables to the antenna ports of the AP at one end and to the outdoor antennas at the other end. { For 2 x 2 MIMO antennas

17 Figure 14 Connect a fiber cable Figure 15 Power injector Power&data outDark failureData inGreen normalPower in (1) Power input cable (2) D

18 NOTE: • If the AP is powered by a PoE+ switch, no power injector is needed. Make sure that the PoE+ switch cansupport the maximum power consum

19 If the AP is connected to the switch through a fiber cable, an SFP transceiver module and a liquid tight adapter are required at the AP side. See

20 Connecting the AP to a power injector To connect the power injector to the AP (see Figure 15): 1. Connect the power input line to an AC power so

21 CAUTION: If the AP is installed outdoor, the Ethernet cable must be waterproof and the connection at the AP port mustbe sealed with waterproof s

22 Logging in to the AP NOTE: A fit AP is zero-configuration and is managed by an access controller or wireless switch. This chapter describes ho

23 Appendix A Crimping an RJ-45 connector You must insert the Ethernet cable through the liquid tight adapter before crimping an RJ-45 connector on t

24 RJ45 pin Signal Wire Signal direction RJ45 pin 2 TX- Orange Æ 6 3 RX+ White-green Å 1 4 — Blue — 4 5 — White-blue — 5 6 RX- Green Å 2 7 — Whi

Preface The H3C WA2620X-AGNP AP Installation Guide describes the hardware specifications of the new generation WA2600 802.11n outdoor AP, preparations

25 Index C E H I O P V C Connecting cables,15 E Examining the AP,8 Examining the installation site,6 H Hardware specifications,1 I Installing the A

Category Documents Purposes Compliance and safety manual Provides regulatory information and the safety instructions that must be followed during in

i Contents Product overview···························································································································

1 Product overview Overview H3C WA2620X-AGNP access point (AP) is a new-generation AP that supports 802.11n and can work in fit or fat mode. A fit AP

2 LEDs Figure 2 WA2620X-AGNP LEDs Table 2 LED description LED Color Quantity Description POWER (Power LED) Green 1 Indicates power status: • On:

3 LED Color Quantity Description 2.4G (802.11g/n LED) Green 1 Indicates wireless link status: • Off: The wireless link is down or fails. • Slow b

4 Figure 3 WA2620X-AGNP port layout (1) 2.4G-3 antenna port (2) 2.4G-2 antenna port (3) 2.4G-1 antenna port (4) 5G-1 antenna port (5) 5G-2 anten