H3c-technologies H3C WX5500E Series Access Controllers Bedienungsanleitung Seite 116
- Seite / 221
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
105
• Before you enable BPDU tunneling for DLDP, EOAM, GVRP, HGMP, LLDP, or STP on a port, disable
the protocol on the port.
• Because PVST is a special STP protocol, you must do two things before you enable BPDU tunneling
for PVST on a port: first, disable STP; second, enable BPDU tunneling for STP on the port.
• Do not enable BPDU tunneling for DLDP, EOAM, LACP, LLDP, PAGP, or UDLD on the member port
of a Layer 2 aggregation group.
Enabling BPDU tunneling
This section describes how to enable BPDU tunneling.
Enabling BPDU tunneling for a protocol in Layer 2 Ethernet
interface view or port group view
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Enter Ethernet interface
view or port group view.
• Enter Layer 2 Ethernet interface view:
interface interface-type
interface-number
• Enter port group view:
port-group manual port-group-name
Use one of the commands.
3. Enable BPDU tunneling for
a protocol.
bpdu-tunnel dot1q { cdp | dldp | eoam
| gvrp | hgmp | lacp | lldp | pagp |
pvst | stp | udld | vtp }
By default, BPDU tunneling is
disabled.
Enabling BPDU tunneling for a protocol in Layer 2 aggregate
interface view
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Enter Layer 2 aggregate
interface view.
interface bridge-aggregation
interface-number
N/A
3. Enable BPDU tunneling for a
protocol on the Layer 2
aggregate interface.
bpdu-tunnel dot1q { cdp | gvrp |
hgmp | pvst | stp | vtp }
By default, BPDU tunneling is
disabled.
Configuring destination multicast MAC address for
BPDUs
By default, the destination multicast MAC address for BPDUs is 0x010F-E200-0003. You can change it
to 0x0100-0CCD-CDD0, 0x0100-0CCD-CDD1, or 0x0100-0CCD-CDD2.
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Verwandte Produkte und Handbücher für Router H3c-technologies H3C WX5500E Series Access Controllers
(4 Seiten)
(18 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern