H3c-technologies H3C WX5500E Series Access Controllers Bedienungsanleitung Seite 54
- Seite / 221
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
43
Configuring load sharing criteria for link
aggregation groups
You can determine how traffic is load-shared in a link aggregation group by configuring load sharing
criteria. The criteria can be source/destination MAC addresses, source/destination service port numbers,
ingress ports, source/destination IP addresses, or protocol numbers, or any combination.
You can configure global or group-specific load sharing criteria. A link aggregation group preferentially
uses the group-specific load sharing criteria. If no group-specific load sharing criteria is available, the
group uses the global load sharing criteria.
Configuration restrictions and guidelines
The load sharing criteria configuration applies to only unicast packets, and can change the load sharing
criteria for unicast packets. Broadcast packets and multicast packets always use the default load sharing
criteria.
Configuring the global link-aggregation load sharing criteria
Ste
p
Command Remarks
1. Enter system view.
system-view N/A
2. Configure the global
link-aggregation load
sharing criteria.
link-aggregation load-sharing mode
{ destination-ip | destination-mac |
destination-port | ingress-port |
source-ip | source-mac | source-port | }
*
By default, the system selects the
global load sharing criteria
according to the packet type.
In system view, the WX5540E switching engine supports the following load sharing criteria and
combinations:
• Load sharing criteria automatically determined based on the packet type
• Source IP address
• Destination IP address
• Source MAC address
• Destination MAC address
• Source IP address and destination IP address
• Source IP address and source port
• Destination IP address and destination port
• Source IP address, source port, destination IP address, and destination port
• Any combination of incoming port, source MAC address, and destination MAC address
Configuring group-specific load sharing criteria
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Enter Layer 2 aggregate
interface view.
interface bridge-aggregation
interface-number
N/A
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Verwandte Produkte und Handbücher für Router H3c-technologies H3C WX5500E Series Access Controllers
(4 Seiten)
(18 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern