H3c-technologies H3C WX6000 Series Access Controllers Bedienungsanleitung Seite 126
- Seite / 179
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
10-12
To do… Use the command… Remarks
Name the channel with a specified
channel number
info-center channel
channel-number
name
channel-name
Optional
See
Table 10-2 for default channel
names.
Configure the channel through
which system information can be
output to the log buffer and specify
the buffer size
info-center logbuffer
[
channel
{ channel-number | channel-name }
|
size
buffersize ] *
Optional
By default, system information is
output to the log buffer through
channel 4 (known as logbuffer) and
the default buffer size is 512.
Configure the output rules of the
system information
info-center source
{
module-name |
default
}
channel
{
channel-number | channel-name }
[
debug
{
level
severity |
state
state } * |
log
{
level
severity |
state
state } * |
trap
{
level
severity |
state
state } * ] *
Optional
See
Default Output Rules of
System Information
.
Configure the format of the
timestamp
info-center timestamp
{
debugging
|
log
|
trap
} {
boot
|
date
|
none
}
Optional
The time stamp format for log, trap
and debugging information is
date
by default.
Outputting System Information to the SNMP Module
The SNMP module receives the trap information only, and discards the log and debugging information
even if you have configured to output them to the SNMP module.
To monitor the AC running status, trap information is usually sent to the SNMP network management
station (NMS). In this case, you need to configure to send traps to the SNMP module, and then set the
trap sending parameters for the SNMP module to further process traps. For more information, see
SNMP in the Network Management and Monitoring Configuration Guide.
Follow these steps to configure to output system information to the SNMP module:
To do… Use the command… Remarks
Enter system view
system-view
—
Enable information center
info-center enable
Optional
Enabled by default
Name the channel with a specified
channel number
info-center channel
channel-number
name
channel-name
Optional
See
Table 10-2 for default channel
names.
Configure the channel through
which system information can be
output to the SNMP module
info-center snmp channel
{ channel-number | channel-name }
Optional
By default, system information is
output to the SNMP module
through channel 5 (known as
snmpagent).
- Configuration Guide 1
- All Rights Reserved 2
- Trademarks 2
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Obtaining Documentation 6
- Technical Support 6
- Documentation Feedback 6
- Table of Contents 8
- 2 Typical Network Scenarios 13
- Unified Switch Networking 14
- 3 Feature Matrixes 15
- 4 Command Matrixes 29
- Introduction 61
- Configuring Ping 61
- Tracert 64
- System Debugging 65
- 6 NTP Configuration 69
- NTP Message Format 71
- Operation Modes of NTP 72
- Symmetric peers mode 73
- Broadcast mode 73
- NTP Configuration Task List 74
- NTP Configuration Examples 83
- delay disper 89
- Root delay: 40.00 ms 89
- 7 SNMP Configuration 93
- SNMP Protocol Versions 94
- MIB Overview 94
- SNMP Configuration 95
- Configuring SNMP Logging 97
- Configuring SNMP Traps 98
- Configuring Trap Parameters 99
- Network requirements 101
- Configuration procedure 101
- 8 MIB Style Configuration 104
- 9 RMON Configuration 105
- RMON Groups 106
- Alarm group 107
- Private alarm group 107
- Configuration Procedure 109
- Configuration Prerequisites 109
- Information Center Overview 115
- System Information Format 120
- 11 NQA Configuration 136
- Basic NQA concepts 139
- NQA Configuration Task List 140
- Configuring the NQA Server 141
- Enabling the NQA Client 141
- Creating an NQA Test Group 142
- Configuring DHCP Tests 143
- Configuring DNS Tests 144
- Configuring FTP Tests 145
- Configuring HTTP Tests 146
- Configuring UDP Jitter Tests 147
- Configuration prerequisites 148
- Configuring UDP jitter tests 148
- Configuring SNMP Tests 149
- Configuring TCP Tests 150
- Configuring UDP Echo Tests 150
- Configuring UDP echo tests 151
- Configuring Voice Tests 152
- Scheduling an NQA Test Group 157
- NQA Configuration Examples 158
- 12 Index 178
Verwandte Produkte und Handbücher für Router H3c-technologies H3C WX6000 Series Access Controllers
(85 Seiten)
(13 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern